A lot of older Hypertherm® Powermax® machines are still out there cutting. The Powermax800, 900, 1000, 1250 and 1650 were built to last, and plenty of them have outlived the torches and parts that came with them.
The power supply usually isn't the problem. The torch and its consumables are. Here's how to keep an older machine cutting with a retrofit torch.
Why parts are getting hard to find
Hypertherm® has been retiring the torches and consumables for these machines. By its own notices, the original Powermax800 consumables have not been available since January 2021, and the original torches for the Powermax900, 1250 and 1650 are no longer available. The Powermax1000 was last built in 2010.
When the parts dry up, a working machine becomes scrap. A retrofit torch stops that from happening.
What a retrofit torch is
A retrofit torch is a current-style hand or machine torch built to plug into an older power supply. Your machine stays the same. The torch on the end of the leads is new, and it runs current Powermax® 65 / 85 / 105 consumables, the same parts sold for the newest machines.
That means two things for an older machine:
- Consumables you can get. You're buying from the most common Powermax® parts range on the market, not hunting for old stock.
- A fresh torch. New leads, new switch, new body. If your old torch was cracked, leaking or cutting out, that problem goes too.
Which retrofit torch fits your machine
| Your machine | Output | Thermacut® retrofit torch | Crosses to |
|---|---|---|---|
| Powermax® 800 / 900 (quick disconnect) | 50 A / 55 A | T-13351 hand torch, 25 ft | 228916 |
| Powermax® 1000 / 1250 / 1650 | 60 A / 80 A / 100 A | T-13155 hand torch, 25 ft | 228788 |
| Powermax® 1000 / 1250 / 1650 | 60 A / 80 A / 100 A | T-13156 hand torch, 50 ft | 228789 |
| Powermax® 1000 / 1250 / 1650 | 60 A / 80 A / 100 A | T-13157 machine torch, 25 ft | 228790 |
| Powermax® 1000 / 1250 / 1650 | 60 A / 80 A / 100 A | T-13158 machine torch, 50 ft | 228791 |
Not sure which machine you have? The model is on the data plate on the back or bottom of the power supply. Send us a photo of it and we'll confirm the torch before you order.
T-13351 for 800 / 900 — $552.44
T-13155 for 1000 / 1250 / 1650 — $595.90
T-13157 machine torch — $979.36
Which consumables to run
The retrofit torches run the Powermax® 65 / 85 / 105 consumable range: shield, retaining cap, nozzle, swirl ring and electrode. The hand torches take the hand-torch stack below; the machine torches take the machine-style shield and retaining cap. The nozzle is the part that changes with amperage. Set the machine's output to the nozzle's rating, never above it.
| Your machine | Hand-torch nozzle | Thermacut® part |
|---|---|---|
| Powermax® 800 / 900 | 45 A (set the machine to 45 A) | T-11378 (crosses to 220941) |
| Powermax® 1000 | 65 A | T-11377 (crosses to 220819) |
| Powermax® 1250 | 85 A | T-11405 (crosses to 220816) |
| Powermax® 1650 | 105 A | T-11840 (crosses to 220990), with the 105 A shield, cap and swirl ring |
The rest of the stack is shared across 45 to 85 A: shield T-11406, retaining cap T-11423, swirl ring T-11861 and electrode T-11883. At 105 A, swap in shield T-11841, cap T-11422 and swirl ring T-11930. The electrode stays the same.
Not sure what each part does? Our post on how a plasma consumable stack works walks through it.
Before you swap the torch
- Check the power supply first. If the machine powers up, the fan runs and the old torch fires a pilot arc, the power supply is likely fine and a new torch is worth it. If the machine is dead, a torch won't fix it.
- Check your air. A new torch won't cure wet or dirty air. See wet air is killing your plasma consumables.
- Keep the old torch's lead length in mind. If you're used to 50 ft, a 25 ft torch will feel short.
- Powermax® 1000 / 1250 owners with a good torch: you may not need a retrofit yet. If only the body is worn, a T60 / T80 torch body kit may get you more years from the torch you have.
Get one
Every retrofit torch carries a one-year warranty and ships anywhere in Canada.
Shop Powermax® replacement and retrofit torches →
Hypertherm®, Powermax® and Duramax® are trademarks of Hypertherm, Inc. THERMACUT® is a registered trademark of THERMACUT, k.s. Thermacut® torches and consumables are aftermarket replacements, not genuine Hypertherm® products, and TorchandTip.com is not affiliated with Hypertherm, Inc. Part numbers are used to identify fitment only.
T-11406 shield
T-11378 45 A nozzle
T-11861 swirl ring
T-11883 electrodes
0 commentaire