ABICOR Binzel® ABICLEANER — Electrochemical Weld Cleaning for Stainless TIG Welds

ABICOR Binzel® ABICLEANER 800 AC and 1000 AC/DC weld cleaning sets, brushes, ABICLEAN electrolyte and spares for stainless steel TIG welds.

← All welding
ABICOR Binzel ABICLEANER 1000 AC/DC with ABICLEAN electrolyte and carbon fibre brush handle

Stainless steel TIG weld cleaning

Take the heat tint off stainless TIG welds without pickling paste, grinding or scratch marks. The ABICOR Binzel® ABICLEANER cleans and passivates the weld in one pass. Dip the brush, clean the seam: one chemical, no pump, nothing to prime.

Both are complete sets: unit, handle with 4 m cable, earth clamp, ABIBRUSH, ABICLEAN electrolyte, container, spray bottle, spanner and an acid-proof storage box. 120 V.

Why the ABICLEANER

Simple to run

Clamp, dip, brush, rinse. There are no flow settings to dial in and no fluid lines to prime, so anyone in the shop can pick it up and get a clean seam on the first try.

One chemical, no neutraliser

ABICLEAN cleans and passivates, and on the 1000 AC/DC it polishes too. Afterwards you rinse with distilled water. There is no separate neutralising chemical to buy, store or dispose of.

No pump to break

You dip the brush in an open container. Pump-fed weld cleaners add a pump, tubing and valves, and every one of those is a part that can clog, leak or fail. Fewer moving parts means less downtime and lower running cost.

How does it work?

Carbon fibre brush moving along a stainless steel weld seam, tarnish removed behind it

Millions of micro-arcs

The carbon fibre brush is wetted with ABICLEAN electrolyte and connected to the unit. At the tip of every fibre a tiny arc forms, more than a million at once, and together they lift the oxide layer and welding residue off the surface.

Cleaned and passivated in one pass

Stainless steel stays corrosion-resistant because of a thin chromium oxide layer. Welding heat breaks it down. The ABICLEANER restores that protective layer while it cleans, so the seam is passivated, not just bright.

No marks, no hydrofluoric acid

Pickling paste is highly toxic and abrasives leave scratches. The brush has over 1.5 million filaments only 7 µm thick, so it follows every contour, reaches inside corners and leaves fine finishes such as brushed or patterned sheet unchanged.

80 A at 100% duty cycle 1.5 million carbon fibre filaments 0% hydrofluoric acid 0 neutralising chemicals

How to do it

  1. Welder in goggles, chemical gloves and apron cleaning a stainless pipe weld with the ABICLEANER

    1Gear up

    Chemical-resistant gloves, safety goggles and an acid-resistant apron. Work with ventilation or fume extraction.

  2. Earth clamp attached to a stainless workpiece with the ABICLEANER brush on the weld

    2Connect

    Clamp the earth cable to the workpiece and plug the handle into the cleaning-tool socket. Switch on. On the 1000 AC/DC, set the selector to cleaning.

  3. Carbon fibre brush being dipped into the ABICLEAN electrolyte container

    3Wet the brush

    Pour a small amount of ABICLEAN into the container and dip the ABIBRUSH. Re-dip whenever the brush starts to dry. Fill the spray bottle with distilled water for the rinse.

  4. Stainless weld with the cleaned section bright and the uncleaned section still tarnished

    4Brush the seam

    Move the brush over the weld with light circular strokes. The tarnish lifts as you go; there is nothing to wait for.

  5. 5Rinse

    Rinse the residue off straight away with distilled or demineralised water from the spray bottle, then wipe dry with paper towels. Hard tap water can leave stains. The seam is clean and passivated.

    Polishing (1000 AC/DC only): set the selector to polishing and work the same way. Polishing takes longer, so rinse with distilled water between passes to keep the part from overheating.

Safety Data Sheet: ABICLEAN is a hazardous product (corrosive). Download the ABICLEAN SDS (PDF) · All Safety Data Sheets

Passer à la liste des résultats

Activez des filtres :

8 articles
Grille de colonnes
Grille de colonnes

Filtrer

Activez des filtres :