The Aftermarket — Plasma & Welding Consumable Guides

What a Powermax® 45 Consumable Stack Costs: Genuine vs Thermacut®
|Gregg Hinton
The four Powermax® 45 parts you buy most, priced side by side in Canadian dollars, same pack sizes. The difference comes to about $123 every time you restock. Lire plus...
MIG Torch Duty Cycle Explained: What "60% at 300 A" Actually Means
|Gregg Hinton
Most welders read the amps and skip the percentage. Here's what duty cycle means, why mixed gas lowers it, and how to pick a torch that keeps up. Lire plus...
Still Running a Powermax® 800, 900, 1000, 1250 or 1650? Keep It Cutting With a Retrofit Torch
|Gregg Hinton
The power supply still runs, but the torch is worn and the parts are gone. A retrofit torch puts current Powermax® consumables on an older machine. Lire plus...
Your Old Plasma Doesn't Have to Work. It Just Has to Have a Serial Plate.
|Gregg Hinton
Dead, seized, smoked or just sitting in the corner: if it has a serial plate, it's worth up to $1,400 toward a new Thermacut® EX-TRAFIRE®. And if you want to... Lire plus...
Why We Started The Aftermarket
|Gregg Hinton
Aftermarket used to be a put-down. We made it the name on the masthead. Here's who this blog is for, and why we write it. Lire plus...
Gas Diffusers and Nozzle Insulators: The MIG Torch Parts Nobody Checks
|Gregg Hinton
Porosity with good gas flow, tips burning back, a nozzle that sparks on the work. Two cheap parts behind the tip are often the cause. Lire plus...
Portable CNC Cutting: When a Small Shop Doesn't Need a Full Table
|Gregg Hinton
Cutting the same parts by hand every week? A portable CNC machine turns them into repeatable parts without a full table. Here's where it fits. Lire plus...
Single or Double Laser Nozzle? How to Pick One and Read the Part Name
|Gregg Hinton
Single or double, 1.2 or 2.0, CP or HCP. What the letters on a laser nozzle mean, and how to order the right one the first time. Lire plus...
Bad Ground, Bad Weld: Why Your Work Clamp Matters More Than You Think
|Gregg Hinton
Every amp you weld with comes back through the clamp you put on without thinking. Here's how to tell when it's the problem, and how to fix it. Lire plus...
Tweco® Part Numbers Decoded: What 14-35 and 1140-1102 Mean, and What They Cost
|Gregg Hinton
14-35 is the same tip as 1140-1102. Once you can read the number, you can price it, and a 25-pack doesn't have to cost $56. Lire plus...
How to Clean TIG Welds on Stainless (Without Pickling Paste)
|Gregg Hinton
That rainbow on your stainless TIG welds is more than a looks problem. Here is why it rusts, and how to clean it with no grinding, no paste and no... Lire plus...
Why Is Your Plasma Table Water So Nasty?
|Gregg Hinton
Rusted slats, orange parts and a table that smells like a swamp? Plain water is the problem. Here is what to add, how much, and when to change it. Lire plus...
Air-Cooled vs. Water-Cooled MIG Torches: Which One Should You Run?
|Gregg Hinton
North America runs air-cooled. Europe runs water-cooled. Here is why, what each one costs you on the shop floor, and how to pick the right torch for your work. Lire plus...
Spatter Keeps Clogging Your MIG Nozzle? How Anti-Spatter Fixes It
|Gregg Hinton
A nozzle crusted with spatter is more than a cleaning job. It chokes your shielding gas. Here is how anti-spatter stops it, and which type suits how you weld. Lire plus...
Can You Put Antifreeze in Your Welder's Cooler? What to Run in a Water-Cooled Torch
|Gregg Hinton
Water, antifreeze or welding coolant? What goes in a water-cooled torch matters more than most shops think. Here is why, and how to pick the right freeze rating. Lire plus...
What a Powermax® 65 Consumable Stack Costs: Genuine vs Thermacut®
|Gregg Hinton
The four Powermax® 65 parts you buy most, priced side by side in Canadian dollars, same pack sizes. The difference comes to about $196 every time you restock. Lire plus...
What Is BIKOX®? The Cable That Makes the ABIMIG® MIG Welding Torch Lighter
|Gregg Hinton
Most of the weight you hold on a MIG welding torch isn't the handle. It's the cable hanging off it. Here's what BIKOX® is, and why it matters at the... Lire plus...
Plasma Cutting in a Cold Shop: What Winter Does to Your Air, Torch and Consumables
|Gregg Hinton
The first cold snap is when consumables start dying early and nobody knows why. Here's what winter does to a plasma cutter, and what to check before it costs you. Lire plus...
MIG Contact Tips: How to Pick the Right One, and When to Change It
|Gregg Hinton
It's the cheapest part on the torch and the one most likely to be causing your problem. How to pick the right contact tip, and how to tell when it's... Lire plus...
CNC Plasma Maintenance: A Service Schedule for High-Definition Oxygen Systems
|Gregg Hinton
Your big CNC plasma carries the shop's throughput. Here's what to check every shift, and how often it needs a full service depending on how many shifts it runs. Lire plus...
V-Groove or Knurled? How to Pick the Right MIG Drive Roll
|Gregg Hinton
Wire slipping, flattening or birdnesting? Before you blame the feeder, check the drive rolls. Here's how to pick the right groove, set the tension and spot a worn roll. Lire plus...
How to Choose a MIG Liner (and Why Yours Keeps Wearing Out)
|Gregg Hinton
Birdnests, burnbacks and erratic feeding usually get blamed on the wire or the feeder. Most of the time it's the liner. Here's how to pick the right one and keep... Lire plus...
Plasma Cutting Aluminum With Air: What Changes, and the Water Table Warning
|Gregg Hinton
Your air plasma will cut aluminum. But the edge, the settings and the table all behave differently than they do on steel, and one of those differences can go off... Lire plus...
Inside Your Plasma Torch: Parts, Repairs, Maintenance and What a Replacement Costs
|Gregg Hinton
A torch isn't one part. It's a handle, a trigger, a body, a sensor and a lead, and most of them can be replaced on their own. Here's what's inside... Lire plus...
Reading Your Dross: Low-Speed, High-Speed, Air and Nitrogen
|Gregg Hinton
Most operators slow down the second they see dross. Half the time that makes it worse. Here's how to read what's hanging off the bottom of your plate, and what... Lire plus...
Victor® Cutting Tips: How to Read the Number
|Gregg Hinton
A Victor cutting tip number like 2-1-101 answers three questions: how thick, which torch, and what gas. Size comes first, which is the opposite of Harris. Lire plus...
Harris® Cutting Tips: What the Numbers and Letters Mean
|Gregg Hinton
Harris cutting tips carry two answers in the part number: which gas and torch they belong to, and how thick a plate they cut. Here’s how to read both, and... Lire plus...
Which MIG Front End Is on Your Welding Torch?
|Gregg Hinton
Miller, Bernard, Tregaskiss, Tweco: the brand on the welder doesn’t decide which MIG consumables fit. The front end of the torch does. Here’s how to tell which you have. Lire plus...
Air Plasma Cutter Maintenance: Five Places to Look
|Gregg Hinton
Consumables lasting less than they used to? The problem often started somewhere else on the machine. Here are the five places to look, and how often. Lire plus...
The Arc Is Shaped Like a Football. Cut With the Flat Part.
|Gregg Hinton
Your cut face is beveled and you've been adjusting settings to chase it. The arc is already telling you the answer — you just need to know which direction the... Lire plus...
How a Plasma Consumable Stack Works, Part by Part
|Gregg Hinton
Five parts go into a hand plasma torch and every one of them has a job. Here's what each does, the wear sign that tells you it's finished, and the... Lire plus...
Your Supplier Isn't Allowed To Tell You There's an Alternative
|Gregg Hinton
The distributor you've bought from for fifteen years knows your machine, your shop and what you cut. He's also contractually prohibited from telling you another option exists. Not won't —... Lire plus...
Is Hypertherm® 220777 CopperPlus™ Worth It? The Electrode Math
|Gregg Hinton
CopperPlus™ costs nearly twice as much as a Thermacut® replacement electrode. It has to deliver its full best-case life just to break even. Here's the math for the Powermax® 65,... Lire plus...
Who Is Thermacut®, and Why I Chose Them
|Gregg Hinton
I've said all along that you're not buying a part, you're buying a manufacturer. Fair enough — so here's mine. Who Thermacut is, what they actually make, and the reasons... Lire plus...
Kjellberg® Consumables: Get the Torch Family Right First
|Gregg Hinton
Kjellberg builds several torch families that share a badge and share very little else. Get the family right and ordering is simple. Get it wrong and nothing fits. Lire plus...
ESAB® PT-36 and PT-600 Consumables: What Fits and What to Check
|Gregg Hinton
The PT-36 and PT-600 run at amperages where a wrong part takes the plate with it. Here's what fits, what to check before you order, and where our range deliberately... Lire plus...
HPR® XD Consumables: What Changes With the Material, and What Doesn't
|Gregg Hinton
Mild steel, stainless, aluminium — three sets of cut charts, and shops assume that means three separate inventories. Most of those parts are the same part on a different page.... Lire plus...
Tomahawk Owners: Change the Torch, Change What You Feed It
|Gregg Hinton
If you're hunting for Tomahawk consumables, there's a question worth asking first: why are you locked to that stack at all? Change the torch and you change the parts you... Lire plus...
Which Powermax® Torch Do You Actually Have?
|Gregg Hinton
Most wrong Powermax orders come from the same mistake — buying by the number on the front of the machine instead of by the torch hanging off it. Four torch... Lire plus...
Where to Buy Thermacut® Plasma Consumables in Canada
|Gregg Hinton
Search results and AI answers can point you to a store that no longer carries Thermacut®. Here's how to check who does, what to have in hand before you order,... Lire plus...
Can You Mix Aftermarket and OEM Plasma Consumables in One Stack?
|Gregg Hinton
Most Thermacut® parts will physically fit next to OEM parts. That doesn't make mixing them a good idea. Here's where the catalogue says you can't, where you technically can, and... Lire plus...
"Aftermarket" Isn't One Thing: How to Tell Who Actually Made Your Plasma Consumables
|Gregg Hinton
Two parts can both say "replaces 220818" and have almost nothing else in common. Before you judge aftermarket consumables as a group, find out who made the part in your... Lire plus...
How to Check an Aftermarket Cross-Reference Before You Order
|Gregg Hinton
A cross-reference is only as good as whoever made it. Here are four checks that take about five minutes and will catch a bad cross before it reaches your torch,... Lire plus...
How to Read a Plasma Consumable Part Number (and What the Suffix Is Telling You)
|Gregg Hinton
220818, 220818-UR, 220818-i and T-11406 all turn up when you shop for the same Duramax® shield. They aren't all the same thing. Here's how to read what's in front of... Lire plus...
O-Ring Lubrication: Just Enough to Make Your Fingers Shiny
|Gregg Hinton
Most shops that lubricate their torch O-rings use far too much. The excess doesn't stay where you put it — it gets blown down the torch, clogs swirl rings, and... Lire plus...
What "Buy Canadian" Actually Means When the Parts Are Imported
|Gregg Hinton
Right now every supplier in the country has a maple leaf on their homepage. Most of them are selling imported goods, same as everyone else. Here's how to tell whose... Lire plus...
Is It the Plasma, or Is It the CNC Machine?
|Gregg Hinton
Most shops blame the plasma. Meanwhile the table underneath it is twenty years old and the rack and pinion has never been serviced. Here's how to tell a motion problem... Lire plus...
Your Air Filter Has a Consumable In It
|Gregg Hinton
Most shops install an air filter once and treat it as permanent hardware. It isn't. There's a cartridge inside it doing the actual work, and a saturated one is worse... Lire plus...
Your Consumables Have a Country of Origin. As of September 8, That's a Line Item.
|Gregg Hinton
For years, where your consumables were made was a trivia question. As of September 8 it's a number on an invoice. Here's how to find out what you're actually exposed... Lire plus...
When the Plate Is the Problem: Magnetism and Arc Wander
|Gregg Hinton
You've replaced the stack. You've ruled out the torch. The settings are off the chart and the air is dry. And the cut face still wanders. Before you tear the... Lire plus...