Spatter Keeps Clogging Your MIG Nozzle? How Anti-Spatter Fixes It

|Gregg Hinton
Spatter Keeps Clogging Your MIG Nozzle? How Anti-Spatter Fixes It

Pull the nozzle off a MIG welding torch that's been run hard without anti-spatter and you'll usually find the same thing: a crust of spatter welded to the inside, closing the opening down a little more every day.

That crust is more than a cleaning job. The nozzle's whole purpose is to deliver an even blanket of shielding gas around the arc. Choke the opening and the gas coverage goes uneven, and poor gas coverage is a leading cause of porosity in the weld. The crust also keeps growing until the nozzle or the contact tip has to be replaced.

Anti-spatter breaks that cycle.

What anti-spatter actually does

Anti-spatter puts a thin film between hot spatter and the metal it lands on. The spatter still flies, but it doesn't fuse to the surface. It brushes or taps off instead of welding itself on.

You can put that film in three places:

  • Inside the nozzle, where gas flow is the issue.
  • On the work and fixtures, so parts need less grinding and brushing after welding.
  • On the consumables in a robotic cell, applied automatically between welds.

Anti-spatter treats the symptom. If spatter has suddenly got worse, check your settings, stickout, gas and the condition of the material before you reach for the can.

Match the type to how you weld

Nozzle tip dip (ABICOR Binzel® ABI-Gel, Cantesco® TD-16). Dip the hot nozzle into the gel between welds, or brush it on. It coats the inside of the nozzle, exactly where spatter builds up and blocks gas flow. Best for manual MIG welding where you stop between welds anyway.

Bulk liquid (ABICOR Binzel® ABI-Shield, Cantesco® AS, Cantesco® ES). Spray or brush onto the work, fixtures and tables. Buy it by the gallon, 5 gallon or drum and fill your own sprayer. ABI-Shield isn't affected by freezing and washes off with water. Cantesco® ES leaves a high-solids film you can weld through while it's still wet.

Aerosol (Cantesco® ES-16-A, Cantesco® QP-16-A). A can on the bench for quick touch-ups. ES-16-A is the same water-based formula as ES. QP-16-A is plant oil based and dries instantly.

Ceramic (Cantesco® CRM-16-A, ABICOR Binzel® ABI-Shield ceramic spray). Ceramic sprays dry to a solid coating that won't drip into the weld and lasts far longer than a liquid film. Cantesco® rates one coat of CRM-16-A at up to 8 hours of welding. Good for long production runs where you don't want to stop and re-coat.

Robotic (ABICOR Binzel® ABI-Mist, ABICOR Binzel® Organic). ABI-Mist is a water-based, oil-free fluid with a low viscosity, made to atomize in robotic misting systems without affecting the seals in the cell. Organic is vegetable-oil based and freeze-resistant.

Check flammability before it goes near the arc

All of the bulk liquids and both tip dips we carry are non-flammable. ES-16-A is a non-flammable aerosol.

CRM-16-A, QP-16-A and the ABI-Shield ceramic spray are extremely flammable aerosols. Read the Safety Data Sheet before you store one or use it near the arc, and keep cans away from heat. Every SDS is on our Safety Data Sheets page.

If your parts are going to paint or powder coat

Ask your finisher what they need before you pick an anti-spatter. If they want silicone-free, Cantesco® TD-16 contains no silicones and the ABI-Shield ceramic spray is silicone-free.

Keep the nozzle in service longer

  • Coat the nozzle before the first weld of the day, not after the spatter has started to build.
  • Knock spatter out while it's still loose. Hammering on a nozzle that's welded shut damages the nozzle and the insulator.
  • Replace a nozzle that's dented, cracked or out of round. It won't hold an even gas pattern no matter how clean it is.
  • Check the contact tip while the nozzle is off. Our guide to MIG contact tips covers when to change it.

Find the right one

The anti-spatter comparison chart puts every anti-spatter and tip dip we carry side by side: base, how you apply it, flammability and sizes.

Shop anti-spatter and nozzle tip dip →

Need new nozzles too? Browse MIG contact tips, nozzles and insulators.


ABICOR® and Binzel® are registered trademarks of Alexander Binzel Schweisstechnik GmbH & Co. KG. Cantesco® is a brand of KEMPER SYSTEM.

0 commentaire

Laisser un commentaire

Veuillez noter que les commentaires doivent être approuvés avant leur publication.