The contact tip is the cheapest part on a MIG welding torch, and it's doing one of the hardest jobs. Every amp of welding current goes through it into the wire, while the wire slides through it at full feed speed, a fraction of an inch from the weld pool.
When a tip is wrong or worn, it shows up as everything else: an arc that wanders, wire that sticks, porosity, a feed problem that looks like the drive rolls. So before you take the feeder apart, look at the tip.
Match the tip to your wire
The size stamped on a contact tip is the wire diameter it's made for. A .035" wire takes a .035" tip, a .045" wire takes a .045" tip. The bore is drilled a touch bigger than the wire so it can feed, but tight enough to pass current cleanly.
- Too big and the wire doesn't make steady contact. The arc goes unstable and spatter goes up.
- Too small and the wire drags or jams.
Aluminum is the exception. Aluminum wire is soft and grows more with heat than steel, so it needs a tip with a slightly larger bore. Tips made for aluminum are labelled that way. Running aluminum through a standard steel tip is a common cause of burnback.
Match the tip to your front end
A contact tip has to fit the torch it goes in. Thread size, length and seat all change from one front end to the next, and a tip from one system won't fit another just because the wire size matches.
That's why the first question is always what's on the front of your torch. Centerfire™, TOUGH LOCK®, Tweco®-style, M-Series, FasTip™ and the ABIMIG® A/AT each take their own tips. Which MIG front end is on your welding torch? walks you through telling them apart.
Standard, tapered or heavy duty
- Standard is what most torches ship with and what most work needs.
- Tapered tips have a narrow nose for getting into tight joints and corners, paired with a tapered nozzle.
- Heavy-duty tips carry more copper to handle higher amperage and longer arc-on time without overheating.
Tip and nozzle work as a pair. Whatever tip you run, the nozzle has to fit the same front end and suit the job.
When to change it
Change the tip when it shows any of these:
- The bore has gone oval. Look down the hole. The wire wears the bore into a keyhole shape over time, and once it's no longer round, contact gets erratic.
- Burnback. The wire has fused to the end of the tip. Sometimes you can snip it free, but a tip that's burned back once has usually lost its shape at the end.
- Spatter you can't clean off. Spatter welded onto the end of the tip changes how the wire comes out of it.
- Signs of overheating. Discolouration or a tip that's started to deform.
- The arc goes erratic and the settings haven't changed.
Don't file, drill or ream a worn tip to save it. You'd be enlarging the bore that was already the problem.
If tips keep dying early
A tip that wears out fast is often telling you about something upstream.
- A worn or dirty liner makes the wire drag, and drag shows up as burnback at the tip.
- The wrong or worn drive rolls feed the wire unevenly.
- A loose tip, or one not fully seated, runs hot and wears fast. Snug it down every time you change it.
Keep spares on the bench
A contact tip costs about as much as a coffee. A welder standing around while someone goes looking for one costs a lot more. Keep a few of each size you run within reach of every torch, and change them before they start costing you weld quality.
Need contact tips? Shop by front end, wire size and type, Centerfire™, TOUGH LOCK®, Tweco®-style, M-Series, FasTip™ and ABIMIG®. Shop MIG welding consumables →
TorchandTip.com sells Binzel® MIG welding consumables across Canada. Bernard®, Tregaskiss®, Miller® and Centerfire™, TOUGH LOCK®, FasTip™ are trademarks of Illinois Tool Works Inc. Tweco® is a trademark of ESAB. ABIMIG® and Binzel® are trademarks of Alexander Binzel Schweisstechnik GmbH & Co. KG. TorchandTip.com is not affiliated with Illinois Tool Works Inc. or ESAB. These names identify the equipment the parts fit.
0 comments