How to Choose a MIG Liner (and Why Yours Keeps Wearing Out)

|Gregg Hinton
How to Choose a MIG Liner (and Why Yours Keeps Wearing Out)

Birdnests at the drive rolls. Burnbacks at the tip. A wire feed that surges, stalls and catches. Most welders blame the wire or the feeder first. Most of the time the problem is the liner.

The liner is the coiled guide that runs the full length of your MIG welding torch cable. It carries the wire from the drive rolls to the contact tip. It's a wear part by design: it wears out so the inside of the torch doesn't. Pick the right one, install it properly and it lasts a long time. Get any of it wrong and it becomes the most expensive cheap part in the shop.

Three things decide which liner you need

1. The wire size

Liners are made for a range of wire diameters, usually two neighbouring sizes. A .035"–.045" liner handles both .035" and .045" wire, and a .052"–1/16" liner handles both of those.

Match the liner to the wire you actually run. The common shortcut is to run one big liner across a station that uses two wire sizes. It works until it doesn't. Thin wire in an oversized liner has nothing holding it straight, so it buckles inside the cable and birdnests. That's one of the slowest, most expensive cleanups in MIG welding. Same rule as contact tips: liner, tip and wire should all be the same size.

2. The wire type

Steel and flux-cored wire run through a steel liner. Aluminum is soft, so it shaves on a steel coil and jams. It needs a nylon or Teflon™ (PTFE) liner with a smooth bore. If you switch to aluminum and keep the steel liner, expect feeding problems within the first spool.

There's also a third option: coated or universal liners, built to run every wire material, whether steel, stainless, flux-cored or aluminum. They're a good fit for a torch that has to handle more than one job.

Even with a universal liner, don't switch wire materials through the same liner. Steel particles left behind in the bore end up in your aluminum or stainless welds, and that contamination shows up as porosity and poor weld quality. If one torch runs two materials, give each material its own liner and swap the liner when you swap the wire.

3. The torch it goes into

This is the one people miss. Torch makers build liners differently, and a liner from one system won't seat in another:

  • Conventional liners for Bernard® and Tregaskiss® MIG welding torches. These are the L-series and 415-series numbers.
  • Conduit liners for Tweco® and Lincoln® MIG welding torches. These are the 42-, 44- and 45-series numbers.
  • Monocoil liners for Miller® M-Series torches.

If you're not sure which system your torch uses, start with the front end. Our guide Which MIG Front End Is on Your Welding Torch? walks through how to tell them apart.

Length: cut it right, not short

Liners come in standard lengths to match the torch cable: 10, 15 and 25 ft are the common ones. You buy the length of your torch, then trim it to fit at installation.

The most common reason a liner fails early is that it was cut too short. That leaves a gap between the end of the liner and the back of the contact tip. The wire has nothing guiding it across that gap, so you get micro-arcing inside the front end, burnbacks and a tip that wears out fast. A liner cut a little long is fixable. A liner cut short is scrap.

How you trim depends on how the liner is held:

  • Floating liners should be compressed slightly when the contact tip threads into the diffuser. That way the liner seats tight against the tip with no gap.
  • Liners held with a set screw are cut to length after the set screw is tightened. Lose that set screw and you've turned it into a floating liner, so the trim length changes.

Whichever type you have, deburr both ends after cutting. A sharp edge pointing into the bore shaves the wire on every inch that feeds past it, and those shavings pack the liner from the inside.

Five reasons liners wear out early

  1. Cut too short. Covered above, and still the number one cause.
  2. Burrs from trimming. One pass with a file or deburring tool on each end prevents it.
  3. Drive roll tension too tight. Over-tightened rolls flatten round wire into an oval. Oval wire drags through the liner and the tip the whole way, wearing both. You want just enough tension to feed without slipping.
  4. Wrong size or type for the wire. Oversized liners birdnest. Steel liners chew up aluminum.
  5. Dirty wire. Anything on the wire ends up packed in the liner: dust, shop grime, surface rust. Cover the spool at the end of the shift, or pull it and store it. It costs nothing and it keeps the liner clean.

One more that rarely gets mentioned: wire comes off the spool with a curl in it. That curl keeps pushing the wire against the liner wall. A wire straightener ahead of the feeder isn't mandatory, but it helps both liner and tip life.

The 30-second liner check

Before you replace a liner, or the drive rolls, or the feeder, do a pull test:

  1. Release the drive roll tension.
  2. Lay the torch cable out as straight as you can.
  3. Pull the wire through the torch by hand.

If the wire pulls through smoothly, your liner is fine and the problem is somewhere else. If you can't pull it through by hand, or it catches and drags, the liner, the wire or both need attention. Do it once on a new liner with fresh wire so you know what "good" feels like for your setup.

Blow it out before you replace it

A liner that fails the pull test isn't always finished. Often it's just packed with shavings and dust. Before you swap it, pull the wire out and blow the liner clean with compressed air. Wear eye protection, because whatever's in there comes out fast.

This matters most on aluminum setups. Soft aluminum wire sheds fine shavings as it feeds, and they build up inside the liner until the wire starts to drag. A regular blow-out keeps the bore clear and can add a lot of life to the liner. If it passes the pull test afterwards, put it back in service. If it still drags, it's worn and it's time to replace it.

Never run without one

It's tempting, when a liner fails mid-job, to pull it out and feed the wire straight through the cable. Don't. Without a liner the wire bounces around inside the cable's open bore. It chews through the internal parts and can wear right through the outside of the cable. A liner costs a fraction of what a new torch cable does. Replace it when it's worn.

Finding the right replacement

Every MIG liner we carry is listed under the part number already on your old liner or its packaging: L3A-15 for Bernard®, 415-35-15 for Tregaskiss®, 42-3035-15 for Tweco®, 194012 for Miller® M-Series. Search that number on our site and it takes you straight to the part. Every product title also states the wire size range, the length and the torches the liner fits.

Shop MIG liners →

All liners are ABICOR Binzel® manufactured and ship anywhere in Canada.


TorchandTip.com is not affiliated with Illinois Tool Works Inc., ESAB or The Lincoln Electric Company. Bernard®, Tregaskiss® and Miller® are trademarks of Illinois Tool Works Inc. or its subsidiaries. Tweco® is a registered trademark of ESAB. Lincoln® is a registered trademark of The Lincoln Electric Company. Teflon™ is a trademark of The Chemours Company FC, LLC. These names are used only to identify the equipment our replacement liners are designed to fit.

0 comments

Leave a comment

Please note, comments need to be approved before they are published.