ABICOR Binzel xFUME ADVANCED high-vacuum fume extraction unit

xFUME® ADVANCED High-Vacuum Fume Extraction Unit

115 V
$8,605.49 CAD
Passer aux informations sur le produit
ABICOR Binzel xFUME ADVANCED high-vacuum fume extraction unit

xFUME® ADVANCED High-Vacuum Fume Extraction Unit

$8,605.49 CAD
Voltage

The high-vacuum unit the xFUME® PRO torches are built for. The xFUME® ADVANCED is ABICOR Binzel®'s mobile high-vacuum extraction system. Two high-speed motors pull welding fume straight off the arc through a fume extraction torch and trap it in two self-cleaning cartridge filters, for one or two welders at once.

See it in action

Etienne Blouin of ABICOR BINZEL USA walks through the xFUME® ADVANCED: the two ports, auto start/stop, filter cleaning, the dust drawer and the controls.

Why the xFUME® ADVANCED

  • High vacuum. More than 18,000 Pa (115 V) or 24,000 Pa (230 V) of negative pressure, enough to pull fume through a torch hose.
  • Two workstations. Two intake ports run two fume extraction torches off one unit.
  • Automatic start/stop. A current clamp on the welding cable starts the unit when you strike an arc and stops it when you finish. One clamp is included; a second is available for the second welder.
  • Self-cleaning filters. Compressed-air pulses clean both HISTec PTFE cartridges automatically after welding stops. The filters capture up to 99.5% of dust over 0.1 µm.
  • Control panel. Adjustable airflow dial, auto/manual switch, hour meter and service light.
  • Easy to move and empty. Four castors, and a dust drawer at the bottom that slides out for emptying.

Which voltage?

Option Best for
115 V (601.0245.1) Lower-parameter work and flat-position welding. Max. airflow 350 m³/h (about 205 CFM). 18 A.
230 V High Power (601.0246.1) Higher welding parameters and the xFUME® PRO 501. Max. airflow 420 m³/h (about 245 CFM). 16 A.

Specifications

Approval CSA
Extraction ports 2 (58.8 mm hose connection)
Filters 2 HISTec PTFE cartridges, 2 × 0.63 m² filter surface
Max. compressed air input 6 bar (87 psi)
Sound level Under 75 dB(A)
Size and weight, 115 V 370 × 370 × 990 mm (14.6 × 14.6 × 39 in), 49 kg (108 lb)
Size and weight, 230 V 513 × 370 × 990 mm (20.2 × 14.6 × 39 in), 56 kg (123 lb)
In the box The unit with both filter cartridges fitted, 5 m extraction hose with 2 connectors (601.0117.1), 1 current clamp, power cable, compressed-air connection and operating manual
Replacement filters HISTec PTFE cartridge 601.0111, sold each. The unit takes two, so order 2 and change both together.

Maintenance

From the ABICOR BINZEL operating manual (single-shift intervals):

  • Run the filter cleaning at least every 2 hours, or when the service light comes on. Replace both filter cartridges together, as set out in the manual.
  • Empty the dust drawer daily.
  • Check the hour meter weekly and the unit for damage monthly.
  • After about 500 operating hours, the motor carbon brushes (115 V) or turbines (230 V) are replaced by a qualified electrician. The unit has two motors or turbines; each replacement part is sold as one piece.

Questions

Do I need compressed air?
Yes, for the automatic filter cleaning.

Do I need to buy a hose and filters separately?
No. The unit ships with both filter cartridges fitted, a 5 m extraction hose and a current clamp. Replacement filters and hose are sold separately.

If I only run one torch, does it use both filters?
Yes. The unit pulls air through both cartridges even with one torch connected, so both load at the same rate. Change them as a pair.

Will it run other brands' fume torches?
Yes. Fume extraction torches from other makers connect to the xFUME® ADVANCED. It is built and tuned for the xFUME® PRO.

New to fume extraction? Watch ABICOR BINZEL's four-minute introduction: what welding fume does in the shop and how to start cleaning the air. Watch the video →

Ships anywhere in Canada. Freight item.

xFUME® and ABICOR Binzel® are trademarks of Alexander Binzel Schweisstechnik GmbH & Co. KG.