Plasma Cutting Aluminum With Air: What Changes, and the Water Table Warning

|Gregg Hinton
Air plasma torch cutting aluminum plate on a cutting table

Can you plasma cut aluminum with air? Yes. Any air plasma cutter that cuts steel will cut aluminum, and that includes EX-TRAFIRE® systems and Powermax® 45XP, 65, 85 and 105 machines. Clean, dry shop air is the most economical way to do it.

But aluminum isn't steel. The edge looks different, the settings are different, and if you cut on a water table there's a safety issue you need to know about before you start. Here's what changes.

What changes when you plasma cut aluminum instead of steel

Use the aluminum cut chart, not the steel one

Aluminum conducts heat away from the cut much faster than steel and melts at a far lower temperature. That changes your speed and your amperage for the same thickness. Your machine's manual has separate cut charts for aluminum. Start there, not from the settings you run on mild steel, then fine-tune with test cuts the same way you would on steel: one change at a time.

Don't assume aluminum means slower, either. On the EX-TRAFIRE® 85 A charts, 1/2" aluminum runs at 57 inches per minute, faster than 1/2" mild steel on the same torch.

Expect a rougher, darker edge

Air contains oxygen, and aluminum oxidizes fast. An air-cut aluminum edge comes out rougher and darker than a steel edge, often a dull grey to black. That's normal. It's the trade-off for cutting with free shop air instead of bottled gas.

Clean the edge before you weld it

That oxidized layer causes porosity if you weld straight over it. Grind or wire-brush the cut edge back to bright metal before welding. Use a stainless brush or a grinding disc kept for aluminum only. One that's been on steel will drag steel into your weld.

Clamp to clean metal

Aluminum carries an oxide skin that doesn't conduct well. Put the work clamp on clean, bare metal, or on the table's slats if they're clean, so the arc transfers and holds. Poor ground on aluminum shows up as hard starts and an arc that wanders.

Keep your air dry

Everything in Wet Air Is Killing Your Plasma Consumables applies double on aluminum. Moisture in the air stream adds to the oxidation on an edge that already oxidizes easily.

How thick can you plasma cut aluminum?

Here's what the EX-TRAFIRE® mechanized cut charts list for aluminum on compressed air, from the 65HD up to the 125HD:

Amperage Pierce up to Edge start up to
45 A 3/8" 5/8"
65 A 1/2" 3/4"
85 A 5/8" 1"
105 A 3/4" 1-1/4"
125 A (125HD) 3/4" 1-1/2"

"Pierce" means starting the cut in the middle of the plate. Past that thickness, start from the edge. These come from the machine-torch charts. By hand, how thick you can go cleanly also depends on how steady your travel speed is, so treat these as the ceiling. One exception: on the 125HD, the 45 A chart stops at 1/4" aluminum, so for anything thicker on that machine, turn the amps up.

Running a Powermax® 45XP, 65, 85 or 105? Your operator manual has the matching aluminum charts for your machine.

What about nitrogen?

Nitrogen works well on aluminum. It gives a clean cut with a smooth finish compared to air. The trade-off is the same as on stainless: in an air plasma cutter you'll give up about 30% of your cut speed and thickness capacity, so use it when the finish matters more than the clock. For everyday aluminum work, clean dry air does the job.

Plasma cutting aluminum on a water table: read this first

This is the one that matters. When aluminum is cut over water, the fine particles and molten spray that fall into the table react with the water and release hydrogen gas. That gas can collect in pockets: under a sheet of plate, under the slats, in the corners of the table. Given time and a spark, it ignites. Shops have had it go off with a bang loud enough to lift plate off the table.

If you cut aluminum on a water table:

  • Use a table built for it. Check with your table manufacturer that it's rated for aluminum and set up so gas can't pool under the plate.
  • Don't leave aluminum fines sitting in the water. The reaction keeps going for as long as the fines are there. Clean the table out after an aluminum job rather than letting the sludge build up over weeks.
  • Don't trap gas. Avoid cutting a large sheet that sits flat on the water and seals a pocket underneath, and never leave a full plate sitting on the table between jobs.
  • Keep steel and aluminum waste apart. Aluminum fines mixed with steel scale is a combination you don't want sitting in a table or a dust collector.
  • Downdraft table? Aluminum dust is combustible. Keep the collector and ductwork cleaned out, and check the collector is rated for aluminum dust.

None of this means don't cut aluminum. It means aluminum needs its own housekeeping.

The short version

  • Air plasma cuts aluminum. Use the aluminum cut chart, not your steel settings.
  • Expect a rougher, darker edge, and clean it back to bright metal before welding.
  • Clamp to clean metal and keep your air dry.
  • On a water table, clean out the aluminum fines and don't let gas pool under the plate.

Running aluminum through a hand torch or a table, the consumables are the same Powermax® or EX-TRAFIRE® stack you already run. Find the right stack for your torch here, or send us the OEM part number and you'll get a price and a fitment answer quickly.

Powermax® is a registered trademark of Hypertherm, Inc. TorchandTip.com is an independent distributor of Thermacut® products and is not affiliated with Hypertherm, Inc.

0 comments

Leave a comment

Please note, comments need to be approved before they are published.