When an arc starts popping, wandering or quitting on you, most welders go after the machine, the wire or the gas first. A lot of the time the problem is at the other end of the cable, at the clamp you put on the work without thinking about it.
That clamp carries every amp you weld with. If the connection is poor, nothing on the torch end can make up for it.
It's not really a "ground"
Everyone calls it the ground clamp, but it's the work connection: the return half of the welding circuit. Current leaves the machine through the torch, crosses the arc into the part, and has to come back through the work clamp and lead to the machine. Lose that path and the circuit is broken. Make it poor and the whole circuit runs on less than it should.
Plasma cutters work the same way. The pilot arc fires inside the torch, but the cutting arc has to transfer to the plate and return through the work clamp. A pilot arc that won't transfer to the work is very often a work-connection problem, not a torch problem.
Signs you have a bad work connection
- An erratic, popping arc that settings don't fix.
- A clamp or cable that's hot to the touch. Resistance makes heat, and heat at the clamp is current that never reached your weld.
- Arc marks or spatter on the clamp jaws, or a clamp that has welded itself to the part.
- Hard starts on a MIG, TIG or stick machine.
- On plasma: a pilot arc that won't transfer, or a cut that won't go through material the machine should handle easily.
- Worn hardware: rounded or pitted jaws, a weak spring, a loose lug, or frayed strands at the cable end.
How to get a good connection
- Clamp to clean, bare metal. Paint, rust, mill scale, galvanizing and oil all add resistance. Grind a spot if you have to.
- Clamp close to the joint or the cut. The shorter the path through the work, the better.
- Clamp to the part you're keeping. On plasma, a clamp on the drop-off loses the circuit the moment the piece falls away.
- Keep current out of places it shouldn't go. Don't let the circuit run through bearings, hinges, hydraulic cylinders or electronics on the way back to the clamp.
- Tighten both ends. Check the lug at the machine as well as the clamp. A loose connection at either end does the same damage.
- Size it for the job. The clamp and cable should be rated at or above the amperage you run.
If the arc is being pushed sideways off the joint, moving the work clamp is also one of the first things to try. Our post on magnetized plate and arc wander covers that in detail.
Picking a clamp
| Clamp | Rating | Best for |
|---|---|---|
| SGC steel clamps | 200, 300 or 500 A | Light shop and farm work on a budget |
| WG steel/brass clamps | 200, 300 or 400–500 A | General shop welding |
| GC copper clamps (Tweco®-style) | 300 or 500 A | Steadier current transfer; copper carries current better than steel |
| FGC flat-jaw clamps (Lenco-style) | 300 or 500 A | Plate and flat work; the wide jaws give a bigger contact patch |
| 513.0004 heavy-duty clamp | 600 A, M10 connection | High-amperage production welding |
| GC-10, GCD-15, GCS-15 | Clamp on a 10 or 15 ft lead | Replacing a worn work lead in one piece |
GC-300 copper, $32.11
FGC-500 flat jaw, $66.90
WG-300 steel/brass, $17.59
GC-10 with 10 ft lead, $74.94
Look after it
Clean the jaws back to bright metal now and then, and replace a clamp when the jaws are burned or the spring has gone soft. Check the cable where it enters the clamp and the lug, which is where the strands break first. A clamp costs less than an hour of chasing an arc problem that was never in the machine.
Get it
Need cable connectors, plugs or gas hose too? See all welding accessories.
ABICOR® and Binzel® are registered trademarks of Alexander Binzel Schweisstechnik GmbH & Co. KG. Tweco® is a trademark of ESAB. TorchandTip.com is not affiliated with ESAB; "Tweco®-style" and "Lenco-style" describe the design only. All other trademarks belong to their respective owners.
0 comments