Can You Put Antifreeze in Your Welder's Cooler? What to Run in a Water-Cooled Torch

|Gregg Hinton
Can You Put Antifreeze in Your Welder's Cooler? What to Run in a Water-Cooled Torch

Plenty of water-cooled welding and plasma torch problems that get blamed on the torch actually start in the cooler. The wrong fluid in the tank doesn't fail on day one. It works fine for a while. Then the torch neck starts to corrode from the inside, the channels scale up, the flow drops off, and one cold weekend the whole loop freezes solid.

The fix is cheap and boring: put the right coolant in, at the right freeze rating, and keep an eye on it.

Why water-cooled at all?

On a welding system, water cooling is a choice, and a good one. A water-cooled torch is much lighter in the hand and far more comfortable to weld with all day. The consumables last longer, which means lower operating costs, and the process runs far cooler for the operator.

It comes with trade-offs. The equipment costs a little more up front, and you have to pay attention to the coolant: flush it and change it out. We'll compare air-cooled and water-cooled welding in more depth in a future post.

On a high-amperage plasma system, it isn't a choice. It's a necessity. At those amperages a torch without liquid cooling wouldn't last five minutes. That's why maintaining the cooling system matters so much. When there's a fault, a restriction in the coolant line or a pump that stops, a $1,000 torch gets cooked almost instantly.

The short answer

Run a coolant made for welding and cutting systems. That means a blend of deionized water, glycol and a corrosion inhibitor, made to a low electrical conductivity. Every coolant we carry is ready to use straight from the jug. You don't mix it with water.

Why a torch isn't an engine

In a truck, coolant runs through a block of cast metal. In a water-cooled torch, coolant runs right past live electrical parts carrying welding or cutting current.

That changes what the coolant has to do. A coolant that conducts electricity speeds up electrical (galvanic) corrosion inside the torch neck and raises the risk of voltage leaking where it shouldn't. That's why coolant for welding and cutting is sold with a conductivity rating:

  • Cantesco® tests its CF-series and CFPG cooling fluids at 3.0 µS or less.
  • ABICOR Binzel® rates BTC-50 NF and BTC-15 below 4 µS.

Automotive antifreeze isn't made or sold to a conductivity rating like that. It's made for an engine, not for a loop that carries current through your torch, so we don't recommend it in a welding or plasma cooler.

Why not just water?

Plain water causes three problems:

  1. It freezes at 32 °F / 0 °C. A shop that drops below freezing overnight, a truck-mounted rig or a machine shipped in winter can freeze the cooling channels in the torch.
  2. It corrodes the system. Without an inhibitor, water works on the pump, the radiator and every metal fitting in the loop.
  3. Tap water carries minerals. They build up as deposits inside the channels and restrict flow. ABICOR Binzel® formulates its coolants to minimize those deposits.

Pick your coolant by the coldest it will ever get

Go by the coldest temperature the coolant will ever sit at, including overnight, over a long weekend, in storage and in transit. Don't go by the temperature while you're working.

Coldest temperature Coolant
Stays above +19 °F / −7 °C Cantesco® CF1 Regular
Down to +10 °F / −12 °C ABICOR Binzel® ABI-CoolECO, Cantesco® CFPG or ABICOR Binzel® BTC-15
Down to +6 °F / −14 °C Cantesco® CF2 Mid
Down to −32 °F / −35 °C Cantesco® CF3 Low or ABICOR Binzel® ABI-Cool
Down to −49 °F / −45 °C ABICOR Binzel® BTC-50 NF
Down to −60 °F / −52 °C Cantesco® CF4 Extreme

In most of Canada, an unheated shop or a rig parked outside needs one of the bottom three rows.

Ethylene glycol or propylene glycol?

The CF range, ABI-Cool and BTC-50 NF are ethylene glycol coolants. They give the widest freeze protection, and their Safety Data Sheets carry a warning: harmful if swallowed.

ABI-CoolECO and CFPG use propylene glycol and are not classified as hazardous. ABICOR Binzel® rates ABI-CoolECO as non-toxic, for areas where people may come in contact with the coolant. The trade-off is that both propylene glycol coolants protect only to +10 °F / −12 °C.

Read the Safety Data Sheet before you store, handle or dispose of any coolant. They're all on our Safety Data Sheets page, in English and French where the manufacturer publishes one.

Keep an eye on it

  • Check the level in the cooler tank before you start. Most coolers have a level indicator or a see-through tank for this.
  • Watch the flow. Many coolers have a flow switch that shuts the system down if coolant isn't moving. If it trips, find out why before you reset it. A kinked hose, a blocked filter or a failing pump will cook a torch.
  • Look at the coolant. It should be clear. Cloudy or discoloured coolant, or anything growing in the tank, means it's time to drain, flush and refill.
  • Don't top up with a different coolant. When you switch products, drain and flush the system first.

How often to flush and replace

Go by how hard the system works, not by the calendar alone:

How you run Flush and replace the coolant
One shift, 3–4 hours of actual arc-on time a day Once a year
Two shifts Every six months
Three shifts As often as every two months

On a plasma system, watch how you change consumables. Do it in a clean environment. Dirt and grit that get into the torch during a consumable change end up in the coolant.

On a liquid-cooled plasma torch, coolant problems show up in the consumables first. Our post on liquid-cooled plasma torch wear covers how to tell when the coolant is the problem, not the parts.

Find the right one

The coolant comparison chart puts every coolant we carry side by side: base, freeze rating, conductivity, safety and sizes from 1 gallon to a 55 gallon drum.

Shop welding and plasma coolants →

Running plasma in a cold shop this winter? See Plasma Cutting in a Cold Shop for what winter does to your air, torch and consumables.


ABICOR® and Binzel® are registered trademarks of Alexander Binzel Schweisstechnik GmbH & Co. KG. Cantesco® is a brand of KEMPER SYSTEM.

0 comments

Leave a comment

Please note, comments need to be approved before they are published.