IndustriFume™ Central Fume Extraction System, 4 to 6 Torches
One central unit for the whole welding bay. The IndustriFume™ is ABICOR Binzel®'s heavy-duty fume extraction unit. It runs 4 to 6 fume extraction torches or hose kits from one cabinet, through flexible hose or hard duct to an overhead system, and suits robotic welding cells too.
Why the IndustriFume™
- 4 to 6 stations on one unit. At about 70 CFM per torch at the nozzle, depending on wire type and amperage. The standard 5" single-opening plenum plate takes one hose or a duct. The optional 2" 6-port plenum plate (284.1709) runs up to six torches directly.
- Up to 99.9% fume removal. The figure depends on the filter you choose.
- Self-cleaning filter. A differential pressure sensor watches the filter, and the programmable AutoPulse controller cleans it with compressed air from a pulse-air reservoir, without stopping the unit.
- Starts and stops with the arc. The Economizer® shunt starts the unit when welding begins and stops it when welding ends. Fifteen minutes after the last arc it drops into sleep mode, which saves energy and keeps the blower turning between jobs.
- Soft start and blower speed control. The motor ramps up instead of starting across the line, so there is no start-up current spike, and blower speed can be managed for less dust build-up and better filter cleaning.
- 28 HP motor. Permanently sealed ball bearings and thermal overload protection, driving a corrosion-resistant aluminum blower housing, impeller and cover.
- Built for the plant floor. Fully welded 10- and 12-gauge steel cabinet, powder-coated, with built-in acoustic lining and a metal-mesh spark arrestor. The electronics sit in a NEMA-12 electrical enclosure, with an interlocking disconnect (the panel door will not open while it is on), motor starter, overload and start/stop button on the front panel.
- Quick filter changes. The vertically mounted filter comes out with a tool-less clamping design and locking lever handles.
- Works with xFUME® source capture. Pair it with xFUME® PRO fume extraction torches or xFUME® ROBO kits.
Which filter?
| Option | Filter |
|---|---|
| MERV 15 filter | Flame-retardant nanofibre, 275 sq ft (replacement 284.1698) |
| MERV 15 filter, VFD | Same filter, unit fitted with a variable frequency drive |
| E11 PTFE filter | Flame-retardant PTFE on 100% spun-bond polyester, 273 sq ft (replacement 284.1699) |
Choose the voltage that matches your plant's three-phase supply: 208/230 V, 460 V or 575 V.
In the box
The extraction unit with an Economizer® soft-start shunt, one filter cartridge (the filter you choose) and a replaceable spark arrestor. The 5" single-opening plenum plate is standard. The 2" 6-port plenum plate (284.1709) and the HEPA exhaust filter (284.2033) are optional.
Specifications
| Open airflow | 710 CFM (1,207 m³/h) |
| Operational airflow | 450 CFM at 110" H₂O |
| Motor | 28 HP |
| Power | 208/230, 460 or 575 V, three-phase |
| Filter area | Up to 275 sq ft |
| Inlet | 5" single-opening plenum plate (standard); 2" 6-port plate optional |
| Filter cleaning | Automatic, programmable AutoPulse controller |
| Compressed air | 70 to 90 psi (4.8 to 6.2 bar), 1/4" industrial quick-connect |
| Electrical enclosure | NEMA 12 |
| Sound level | 75 dBA at 5 ft |
| Size | 62" H × 31" W × 71" D |
| Weight | About 1,166 lb (529 kg) |
Electrical
A qualified electrician must make the power connection, and the branch circuit protection is supplied by you. Figures from the ABICOR BINZEL operator manual:
| Supply | Unit full-load amps | Recommended breaker | Supply wire |
|---|---|---|---|
| 208 V, 3-phase | 89.7 A | 150 A | 2 ga |
| 230 V, 3-phase | 81.6 A | 125 A | 2 ga |
| 460 V, 3-phase | 40.8 A | 60 A | 6 ga (or 2 SO cable) |
| 575 V, 3-phase | 29.8 A | 50 A | 8 ga (or 4 SO cable) |
Installation
It arrives crated on a pallet on a flatbed, so plan for a forklift. The unit is top-heavy on the motor side, has four lifting lugs on top and eight floor-mounting holes in the base flange. Ducting from the 5" inlet, or hose from the 6-port plate, is supplied by you. Compressed air must be clean, filtered and regulated to 70 to 90 psi.
Maintenance
Check and empty the catch basin under the filter every four to six weeks at first, then set your own interval by how much dust you find. Shutting down with the stop button lets the unit run its offline cleaning cycle, which extends filter life. Keep a filter log; the manual includes one.
Not for combustible dust. The unit collects residue that may be flammable. It is not recommended for highly combustible or explosive materials.
Warranty
Twelve-month limited warranty from ABICOR BINZEL from the date of shipment. Filters and other consumables are not covered, and using non-genuine ABICOR BINZEL replacement parts voids the warranty.
Questions
Will it run on 208 V?
Yes. The 208/230 V version runs on either three-phase supply.
Do I need compressed air?
Yes, 70 to 90 psi, for the automatic filter cleaning.
Can I connect it to ductwork?
Yes. It connects to flexible hose or to hard duct running to an overhead system.
How is it shipped?
By freight. It weighs about 1,166 lb. We email you the freight cost to your site before it ships.
New to fume extraction? Watch ABICOR BINZEL's four-minute introduction: what welding fume does in the shop and how to start cleaning the air. Watch the video →
Ships anywhere in Canada. Freight item.
IndustriFume™, xFUME® and ABICOR Binzel® are trademarks of the ABICOR Binzel group. Economizer® is a trademark of its owner.