TIG weld a piece of stainless and the seam comes out wearing a rainbow: straw, gold, blue, purple, sometimes grey. Some welders are proud of that colour. Your customer usually isn't, and on stainless it's more than a looks problem.
What that colour actually is
That rainbow is heat tint: an oxide layer that forms on the surface when the steel is hot enough to react with the air around the weld. Underneath it, the welding heat leaves a thin layer of metal that has lost some of its chromium.
Chromium is what makes stainless stainless. It forms the thin, invisible film that protects the surface from rust. TWI, the UK welding research institute, says the oxide scale and the chromium-depleted layer formed during welding must be removed to keep the steel's corrosion resistance.
So a stainless part with heat tint left on the welds can rust at the welds, even though the rest of the part is fine. On food equipment, railings, tanks, marine parts and architectural work, that's a callback.
Pickling paste alternatives: three ways to clean heat tint
The short answer: our pick for a pickling paste alternative is electrochemical weld cleaning. It lifts the heat tint and passivates the surface in the same pass, and the ABICLEAN electrolyte we stock does it without hydrofluoric acid. Here is how the three options compare.
Grinding or brushing. Fast and cheap, but it changes the surface finish, it's hard to do in a tight fillet, and a wire brush or blast doesn't remove the chromium-depleted layer.
Pickling paste. Brush it on, wait, rinse it off, neutralise it. It works, but conventional pickling products contain nitric acid and hydrofluoric acid. HF is one of the nastiest chemicals in any shop, and you're dealing with the waste rinse water too.
Electrochemical cleaning. A low-voltage unit, a conductive brush and an electrolyte. The current and the electrolyte lift the oxide layer and passivate the surface in the same pass, so the protective film can re-form. No grinding, no abrasives, and no waiting on paste.
How the ABICOR Binzel® ABICLEANER works
The ABICLEANER is an electrochemical weld cleaner for stainless TIG welds. The job goes like this:
- Clamp the ground clamp to the part.
- Dip the carbon fibre brush in the ABICLEAN electrolyte.
- Brush the weld seam. The heat tint lifts as you go.
- Rinse with distilled water and wipe dry.
That's it. No flow settings to dial in and no fluid lines to prime.
Why we went with the ABICLEANER
- It's simple to run. Clamp, dip, brush, rinse. There is very little to learn.
- One chemical does the job. ABICLEAN cleans and passivates in the same pass. On the ABICLEANER 1000 AC/DC, the same bottle polishes too. One bottle on the shelf, not three.
- There's no pump to break. You dip the brush in an open container. Pump-fed weld cleaners add a pump, tubing and valves that can clog, leak or fail. Fewer moving parts means less downtime and a lower running cost.
- No hydrofluoric acid. The ABICLEAN all-in-one electrolyte cleans and passivates without the HF in conventional pickling products.
- It gets into the corners. The ABIBRUSH carbon fibre brush has about 1.5 million fine filaments that reach into fillets and narrow gaps a grinder can't.
800 AC or 1000 AC/DC?
| ABICLEANER 800 AC | ABICLEANER 1000 AC/DC | |
|---|---|---|
| Cleaning (AC) | Yes | Yes |
| Polishing (DC) | No | Yes |
| Power | 800 VA | 1000 VA |
| Mains | 120 V / 60 Hz | 120 V / 60 Hz |
| Weight with accessories | 25.4 lb (11.5 kg) | 30.9 lb (14 kg) |
| Price (CAD) | $2,511.36 | $4,533.75 |
Pick the 800 AC if you need clean, passivated TIG welds and the finish around them is already good enough.
Pick the 1000 AC/DC if your work also needs a polished, bright finish, for example on food, pharma or architectural stainless.
Both ship as a complete set: the unit, a handle and a ground clamp on 13 ft (4 m) cables, the ABIBRUSH and PTFE sleeve, 1 L of ABICLEAN, an electrolyte container, a spray bottle for distilled water, a spanner and an acid-proof carry case.
Keep it running
Brushes, PTFE sleeves and electrolyte are the parts that wear and get used up. Keep a spare brush and a bottle of ABICLEAN on the shelf so a job never stops for a part:
- ABIBRUSH carbon fibre brush: $83.13
- ABICLEAN electrolyte: 1 L $92.89, 5 L $338.23
- PTFE sleeve: $159.16
Work safely
The electrolyte is corrosive. Wear gloves, goggles and acid-resistant clothing, and work with ventilation or fume extraction. Rinse any splash with plenty of water. The brush and the part get hot. People with pacemakers should not run the unit or stand near it. Indoor use only. Read the ABICLEAN Safety Data Sheet before you start. It's on our Safety Data Sheets page.
Get it
Shop ABICLEANER weld cleaning →
Every set and spare ships anywhere in Canada.
ABICOR® and Binzel® are registered trademarks of Alexander Binzel Schweisstechnik GmbH & Co. KG.






0 comments