A handheld air plasma cutter can get away with a twice-a-year once-over. A high-definition oxygen CNC plasma system can't. It runs at 200, 300, 400 amps, it's liquid-cooled, it runs several gases through a gas console, and it's usually the machine carrying the shop's whole production schedule. When it goes down, everything behind it waits.
This post is the service schedule for that class of machine: the big mechanized systems running oxygen on mild steel, such as the Hypertherm® HPR® and XPR® families, the Kjellberg® HiFocus line and the Lincoln Electric® FineLine LC300M. If you're running an air plasma like a Powermax® or an EX-TRAFIRE®, our air plasma maintenance post is the one you want.
Before you touch anything
Lock the system out. Power off at the disconnect, gases shut off at the supply, and the lockout on the disconnect, every time.
These systems carry lethal voltages, and the power supply's capacitors can hold a charge after the machine is switched off. So the work splits two ways, and the two don't overlap.
Yours: consumables, the torch and its O-rings, coolant level and condition, coolant and gas filters, the torch leads and hoses, ground connections, gas supply leak checks, and cleaning dust out of the cabinets following your operator manual.
A qualified service technician's: anything electrical inside the power supply or gas console. Boards, chopper modules, contactors, testing with a meter. If cleaning turns up a burnt smell, a scorched part or a loose wire, close it up and call a tech.
Every shift
- Consumables. Pull the stack and look at it. On an oxygen system the electrode's hafnium insert and the nozzle bore tell you most of what you need to know. How a plasma consumable stack works covers each part.
- Torch O-rings. Dry, cracked or torn means replace. A light coat of silicone grease, just enough to make your fingers shiny.
- Coolant level. Check the reservoir. A level that keeps dropping is a leak somewhere, even if you can't see it yet.
- Gas pressures. Read the supply and console pressures before the first cut, for every gas the job uses. A pressure that's drifted is cheaper to catch now than in a scrapped part.
- A wet stack. If the consumables come out wet, stop and find the leak before you cut again. On a liquid-cooled torch, moisture where it shouldn't be is the first sign of a cooling problem, and cooling problems destroy whole stacks at once.
The full service
This is the bigger job, and it's where the shop's schedule decides the interval. A full service covers:
- Coolant. Drain, flush and refill with the coolant your system's manual specifies. Plasma coolant is formulated for electrical conductivity as well as heat transfer, so plain water or automotive antifreeze don't belong in these systems.
- Coolant filters. Replace them.
- Gas filters. Check and replace the filters on the gas supply lines.
- Gas leak check. Every fitting from the supply to the console to the torch. Oxygen leaks are a fire risk, not just a wasted-gas problem.
- Torch leads and hoses. Run them end to end along the CNC track. Look for chafe points, kinks, collapsed hoses and cracked jackets, especially where the leads flex the most.
- Grounds. Work lead connection at the table, table ground, and the ground at the power supply. Clean, tight and not corroded.
- Cabinet cleaning. With the system locked out, clean dust out of the power supply and cooler following your manual. Conductive dust and blocked airflow cost you performance long before they throw a fault.
- The torch itself. Threads, the electrode seat and the cooling tube, if your system has one. If the problems keep coming after a fresh stack, the torch may be worn.
How often
The interval follows how hard the machine works, not how old it is.
| Shop schedule | Full service |
|---|---|
| One shift | Every 6 months |
| Two shifts | Every 3 months |
| 24/7 | Monthly |
Plus the every-shift checks above, no matter how many shifts you run.
Don't forget the table
A perfect plasma system on a worn table still cuts bad parts. Rack and pinion, rails, the torch height control slide and the slats all need their own schedule. Is it the plasma, or is it the CNC machine? has the table side of it.
Why it pays
A big oxygen system is the most expensive machine on most shop floors to have sitting still. The every-shift checks take minutes. The full service takes a few hours on a planned day. An unplanned failure takes a stack, sometimes a torch, and the production days that go with it.
If you're tracking consumable cost per arc-on hour, a maintenance problem will usually show up there first.
Need consumables for your CNC plasma? Our guided finder walks you from your machine, material and amperage to the complete stack, in the order the parts go into the torch. Find your consumables →
TorchandTip.com sells Thermacut® aftermarket plasma consumables and Binzel® MIG welding consumables across Canada. Thermacut® is an independent manufacturer. TorchandTip.com is not affiliated with, authorized by, or endorsed by Hypertherm®, ESAB®, Lincoln Electric®, Kjellberg®, or any other original equipment manufacturer. All OEM names, model numbers, and part numbers are used for identification and reference purposes only.
0 comments